PDF Publication Title:
Text from PDF Page: 007
Capstone Turbine Corporation • 21211 Nordhoff Street • Chatsworth • CA 91311 • USA Technical Reference: Stand Alone Operation – Capstone Model C30 and C60 Activating Stand Alone Power Output The system will transition to produce output power in the Load state (closes output contactor) when battery voltage and base battery state-of-charge reaches at least 60 percent. To enable Stand Alone power output: • CRMS: From the main panel, click on the Power ENABLE button. • Display panel: Press and hold the INTERLOCK and ENABLE buttons simultaneously. This signal may be automated with the Auto Load software feature. When the Auto Load dispatch mode is enabled, it automatically issues an Enable command when the system is ready to support the connected loads. De-activating Stand Alone Power Output The system can be commanded to manually deactivate output power (open output contactor) and return to the Run state where it will remain operating with fuel. To deactivate Stand Alone power output: • CRMS: From the main panel, click on the red DISABLE button. • Display panel: Press and hold the INTERLOCK and DISABLE buttons simultaneously. Once an output power disable command has been given, the system must be manually commanded to again deliver output power, even if the Auto Load software feature had been previously enabled. Stopping Stand Alone Operation The MicroTurbine immediately ceases supplying output power (output contactor opens) when a system STOP or OFF command is issued, or when a severity level 3 fault (other than a flameout) occurs. An explicit OFF command will override any dispatch mode settings, and is stored by the system. A system OFF first disables power output and transitions to the Recharge state. Then, the system continues operating with fuel to charge the battery to 90-95 percent state-of-charge, which can take up to 20 minutes. Finally, the MicroTurbine shutdown process initiates a cooldown period, which can last up to 10 minutes. To halt MicroTurbine operation: • CRMS: From the main panel, click on the red STOP button. • Display panel: Press and hold the INTERLOCK and STOP buttons simultaneously. Initiating an Emergency Stop WARNING Repeated use of the optional Emergency Stop switch will result in damage to the MicroTurbine. Use only in emergency situations. If an optional emergency stop (E-stop) has been installed, the E-stop switch may be activated. Activating E-stop immediately shuts off the fuel and electrical output. This causes the compressor bypass valve to open, venting the compressed air out of the MicroTurbine and causing it to coast to a stop. After an emergency stop, power to the MicroTurbine must be turned off for 30 seconds before a restart can be attempted. Emergency stops should NEVER be used for routine shutdowns. Emergency stops increase stress on the system components and will result in reduced service life of the MicroTurbine. 410028-001 Rev. C (July 2004) Page 7 of 22 This information is proprietary to Capstone Turbine Corporation. Neither this document nor the information contained herein shall be copied, disclosed to others, or used for any purposes other than the specific purpose for which this document was delivered. Capstone reserves the right to change or modify without notice, the design, the product specifications, and/or the contents of this document without incurring any obligation either with respect to equipment previously sold or in the process of construction.PDF Image | Stand Alone Operation – Capstone Model C30 and C60
PDF Search Title:
Stand Alone Operation – Capstone Model C30 and C60Original File Name Searched:
stand_alone.pdfDIY PDF Search: Google It | Yahoo | Bing
Capstone Turbine and Microturbine: Capstone microturbines used and new surplus for sale listing More Info
Consulting and Strategy Services: Need help with Capstone Turbine, sizing systems, applications, or renewable energy strategy, we are here to assist More Info
Container Lumber Dry Kiln: Since 1991 developing and innovating dry kilns using standard shipping containers More Info
Supercritical CO2 Lumber Dry Kiln: Compact fast drying in 3 days or less for small amounts of wood and lumber drying More Info
BitCoin Mining: Bitcoin Mining and Cryptocurrency... More Info
Publications: Capstone Turbine publications for microturbine and distributed energy More Info
FileMaker Software for Renewable Energy Developing database software for the renewable energy industry More Info
CO2 Gas to Liquids On-Demand Production Cart Developing a supercritical CO2 to alcohol on-demand production system (via Nafion reverse fuel cell) More Info
Stranded Gas for low cost power Bitcoin Mining Using stranded gas for generators may provide breakthrough low power costs for cryptocurrency miners. More Info
| CONTACT TEL: 608-238-6001 Email: greg@globalmicroturbine.com | RSS | AMP |