logo

FURNACE-TYPE LUMBER DRY KILN: REFRESHED EDITION | Sawdust-fired heat-pipe kiln, stainless U-tube container build, and the Conifer sawdust burner

GLOBAL ENERGY LLC  •  INFINITY TURBINE LLCwww.infinityturbine.com

Refreshed from USDA Forest Products Laboratory Report R1474-A (1945)

A sawdust-fired heat-pipe kiln: a Conifer burner fires a 16 in stainless U-tube, the fans blow over it, and clean hot air dries the lumber. No boiler, no steam, free fuel.

  • 28 pages
  • Clean line drawings
  • Build photos
  • Sizing & checklists
  • Conifer burner data
See what's inside
Conifer sawdust burner on its hearth
Container kiln shell with doors open
16 inch stainless U-tube with welded segmented return bend
Burner fire door open showing cast liner

Dry lumber and firewood with mill sawdust

In 1945 the USDA Forest Products Laboratory in Madison, Wisconsin, built and ran an experimental furnace-type kiln. A sawdust burner fired a return-bend flue pipe inside the kiln. The flue gas stayed inside the pipe, the pipe heated the air, and fans moved that clean, hot air through the load. Over 14 charges in a year it dried even difficult woods such as oak to standard kiln schedules.

This refreshed edition reorganizes that report for today's builders and redraws every figure. It adds a modern build: a shipping-container kiln heated by a Conifer sawdust burner firing through a 16 in stainless steel U-tube, plus the Conifer burner literature for installation, operation and selection.

It is a practical reference for sawmills, woodworkers, firewood producers and anyone with a steady supply of sawdust or chips who wants low-cost kiln heat.

How the heat-pipe kiln works

The burner and the drying chamber are separated. Only the stainless pipe crosses the partition, so the lumber sees warm, clean air and never the flue gas.

  1. Burn the sawdust

    The Conifer burner in the heater room feeds green sawdust by gravity from its hopper. A thermostat opens and closes the draft door to hold the dry-bulb temperature.

  2. Heat the pipe

    Hot gas rises up a stainless riser to the ceiling, runs down leg A, around the welded segmented bend and back up leg B to the chimney: about 62 ft of 16 in pipe.

  3. Blow over the pipe

    In the twin-container (16 ft wide) kiln, the fans sit between the wall and the ceiling-mounted pipe and blow downwind over both legs, above a sheet-metal fan deck.

  4. Dry the load

    Hot air drops down the far wall, crosses the lumber packs and returns to the fans. Vents release moisture; a water spray on the hot leg raises humidity when needed.

B3 cross section and pipe details
Page B3: cross section of the twin-container kiln with the U-tube hung just below the ceiling, downwind of the fans, plus the return bend, roller hanger and burner riser details. Click to enlarge.

The build, in real photos

The Global Energy / Infinity Turbine container kiln: Conifer burner, cast fire door, the 16 in stainless U-tube and the container shell.

What's inside

Three parts, written for builders and operators. Text pages print portrait; drawings print landscape on US Letter.

PART A

The FPL furnace-type kiln

  • Heating system design and general arrangement
  • Operating the sawdust burner; fuel and burn rates
  • Humidity control with a wood-element hygrostat and water sprays
  • Instruments, air circulation and kiln samples, with formulas
  • 1945 operating cost, fire hazards and conclusions
  • Temperature-uniformity table and redrawn drying records for oak and maple

PART B

Stainless U-tube container kiln build

  • Design summary and build photos
  • Plan and side elevation of the twin-container kiln
  • Cross section, return bend, roller hangers and burner riser
  • Sizing: heat exchanger output, burner, chimney and fuel
  • Operating and fire-safety checklist

PART C

The Conifer sawdust burner

  • How the burner works; fuels it can and cannot burn
  • Cutaway of the Conifer wood-burning system
  • Estimating and selection data sheet
  • Installing the No. 12 burner, with part numbers
  • Operating S-type burners; shaking-grate parts

Sample drawings

Every figure is redrawn as a clean line drawing. Click any sheet to enlarge.

B2 plan and side elevation
B2  U-tube kiln: plan and side elevation
B3 cross section and pipe details
B3  Cross section and pipe details
A8a drying records
A8a  Drying records for oak and hard maple (redrawn)
C1a Conifer cutaway
C1a  Conifer wood-burning system: cutaway (redrawn)

Key numbers

From the sizing page and the original FPL report.

~259 sq ft
Heated pipe surface in the kiln
204k–340k
Btu/h estimated U-tube output
312,000
Btu/h, Conifer No. 12 rating
~40 lb/h
Average green-oak sawdust burn at FPL
Conifer modelOutput to heating unitGrate areaChimney
No. 12312,000 Btu/h2.06 sq ft8 in × 30 ft
No. 14510,000 Btu/h3.44 sq ft12 in × 35 ft
21-S750,000 Btu/h5.00 sq ft16 in × 35 ft

A No. 12 closely matches what the 16 in U-tube can transfer and what a 5,000 BF hardwood charge needs. Output figures are planning estimates; measure flue-gas temperature at the outlet to confirm.

!

Take the fire hazard seriously

Many early direct-heated and furnace-type kilns burned down. The publication collects FPL's findings on backfiring burners, hopper fires and hot pipe sections, and turns them into a pre-lighting, operating and shutdown checklist.

Check local codes and your insurer before building or operating a wood-fired kiln.

Furnace-Type Lumber Dry Kiln: Refreshed Edition

FPL report R1474-A, a stainless U-tube container kiln build and the Conifer sawdust burner literature, in one 28-page illustrated PDF.

CONTACT Email: greg@globalmicroturbine.com | AMP | PDF